Product Image |
Item Name- |
Price |
 |
As fitted to the 1071 S, sits behind the rocker cover. The 90 degree bend is not quite as tight as the original, but fits OK Made with copper tube |
£16.50
Add:
|
 |
This is the hose that goes from the outlet on top of the rocker cover and to the standard air filter box on all early Minis and the variants. These... |
£7.60
Add:
|
 |
Rubber over wire, Approx 37 inches long. For some reason left hand drive are listed as been 29 inches long ? |
£55.00
Add:
|
 |
Originally welded to the inside of front panel. Made with stainless steel mesh grill and zinc electroplated. A point to note - these are suited more... |
£18.00
Add:
|
 |
As fitted to MKI minis and variants. Original style tube of rubber material wrapped over a wire coil. As an improvement to the original design, these... |
£61.00
... more info

|
 |
Ball joint cover made from automotive grade EPDM, not the cheap rubber stuff that only lasts a couple of months. This is like the early MOWOG style... |
£1.75
Add:
|
 |
Ball joint cover made from automotive grade EPDM, not the cheap rubber stuff that only lasts a couple of months |
£1.75
Add:
|
 |
For LHD cars. Fits to bulkhead under speedo hole. Made from stainless steel. Price is for one unit (two shown in the picture only to show profiles) |
£3.00
Add:
|
 |
Stainless steel brake pipe clip for the bulkhead on LHD cars |
£3.20
Add:
|
 |
The hose that connects the breathers to where ever is needed. 1/2 inch (12.5mm)internal bore, they have a rough "wrapped" finish and are 18 inches... |
£12.50
Add:
|
 |
For the bulkhead where the heater hoses pass through. See 14A9976 for the upper or ALA6599 for the lower hydro version. Finish = powder coat |
£7.30
Add:
|
 |
For the bulkhead where the heater hoses pass through, for hydro cars. Also known as ALA5557. See 14A9976 for the upper or 14A6735 for the lower dry... |
£11.50
Add:
|
 |
For the bulkhead where the heater hoses pass through. See 14A6753 or ALA6599 for the lower. (also known as part ALA7530) Large holes are 7/8"... |
£7.20
Add:
|
 |
For the brake T piece, fits to the clutch hose bracket. See 21A2522 for the hydro version. Finish = powder coat |
£4.50
Add:
|
 |
For the brake T piece, fits to the clutch hose bracket. See 21A1116 for the dry version. Finish = zinc plate |
£6.50
Add:
|
 |
A pair of spanners to make adjusting the clutch so much easier. The open ended spanner sits on the inner nut and the ring spanner on the outer. If... |
£12.00
... more info

|
 |
The large grommet that fits over the large rubber air tube and into the bulkhead |
£4.90
Add:
|
 |
Hardened washers that sit under the cylinder head nuts. Also known under PWZ106 Priced each |
£0.25
Add:
|
 |
This is the 1/2" OD short tube that connects the heater pipe to the bottom hose. Made from copper so will not rust away like the original steel ones |
£3.50
Add:
|
 |
Short large diameter tube for the external blower on early cars. Rubber over wire. These are a tight fit and may need squashing a bit to get a... |
£25.00
... more info

|